Modular process skids are widely used in industrial projects where pumps, valves, instruments, piping and other equipment are assembled into transportable packages before being delivered to the installation site. These packages are designed to simplify fabrication, reduce on-site construction work and support faster project deployment.
Platform flooring is an important part of skid design. Maintenance personnel need safe access to operating equipment, while the platform must fit within the skid's structural frame, transportation envelope and installation sequence. Fiberglass reinforced plastic (FRP) grating can be considered for these platforms when its structural properties, environmental resistance and project requirements are suitable.
Using FRP grating in a modular skid is not simply a matter of replacing steel floor panels. Panel dimensions, support locations, equipment clearances, removable access areas and shipping arrangements should be coordinated during the engineering and fabrication stages.
1. Why Consider FRP Grating for Modular Process Skids?
Modular skids are often fabricated in workshops and transported to remote or industrial sites. Their flooring materials therefore need to satisfy both operational and logistical requirements.
Reduced platform weight
FRP grating is generally lighter than comparable steel grating configurations. Reducing platform weight can help control the overall weight of a packaged skid, which may be relevant when planning lifting operations, transportation and site handling. The actual weight difference depends on the grating type, depth, resin system and support arrangement.
Corrosion resistance
Process skids may operate in environments exposed to moisture, chemical splashes, salt, cleaning agents or outdoor weather. FRP can offer corrosion resistance in applications where conventional steel flooring would require additional protection or more frequent maintenance. Resin selection and chemical compatibility should always be checked against the actual process environment.
Open-grid drainage and ventilation
The open structure of FRP grating allows liquids to drain through the floor and can help reduce standing water on the platform. It also allows air and light to pass through the flooring. These characteristics may be useful around pumps, piping and equipment that require regular inspection or cleaning.
Electrical and operational considerations
Some FRP grating products have electrically non-conductive characteristics. This may be relevant to skid packages containing electrical or instrumentation equipment. However, standard FRP grating should not automatically be treated as an electrical insulation system or as certified protection against ignition. Project-specific electrical, static-control and hazardous-area requirements must be reviewed separately.

2. Plan the Platform Layout Around Equipment
The platform layout should be developed together with the equipment arrangement rather than treated as a separate flooring package. A well-planned layout provides practical access to operating components without creating unnecessary obstructions.
Identify routine operating and maintenance points
Start by identifying the components that personnel need to reach during normal operation and maintenance. These may include:
- Pump motors, couplings and mechanical seals.
- Manual valves, actuators and control valves.
- Pressure gauges, flow meters and local instruments.
- Filter housings, strainers and inspection points.
- Electrical junction boxes and instrument panels.
The platform should provide suitable standing areas and access routes for the tasks expected at each location. Equipment removal paths and lifting requirements should also be considered. A walkway that is adequate for routine inspection may not provide enough clearance for removing a motor or valve assembly.
Coordinate platform levels and equipment elevations
Skid layouts may contain equipment installed at different elevations. Designers should coordinate grating levels with pipe centerlines, valve handwheels, instrument displays and equipment access points. Where several platform levels are required, transitions should be designed to avoid unexpected steps and awkward maintenance positions.
Keep access routes clear
Pipework, cable trays and instrument tubing should not unnecessarily obstruct the walking surface. Where services must cross a platform, their routing and protection should be coordinated before the grating is cut or installed.
3. Divide the Grating into Practical Panel Sections
Panelization is one of the most important decisions in modular skid platform design. A single large grating panel may be difficult to handle, transport or remove for maintenance. Smaller sections can provide more flexibility, but excessive joints may complicate installation and create additional detailing requirements.
Match panel dimensions to the skid frame
Grating panels should be arranged according to the actual support frame and bearing direction. Each panel must have adequate bearing on its supporting members, and panel edges should not be left unsupported unless the system has been specifically engineered for that condition.
For pultruded grating, the load-bearing bar direction is particularly important. The panel orientation should be coordinated with the support spacing and the manufacturer's load tables. Cutting a panel into a convenient shape does not remove the need to verify its remaining span and support conditions.
Use removable panels where access is needed
Removable grating sections can be useful above equipment that requires periodic inspection, cleaning or replacement. Examples include pump components, strainers, drain points and concealed piping connections.
These sections should be identified clearly on the fabrication drawings. Their dimensions, lifting method, fastening arrangement and storage location should be considered so that maintenance personnel can remove and reinstall them safely.
Coordinate joints with structural members
Panel joints should preferably align with suitable support members. This helps provide clear bearing conditions and makes the fastening details easier to inspect. Joint locations should also avoid interfering with equipment foundations, pipe supports and other skid components.
4. Coordinate Grating with Structural Supports
FRP grating is a flooring component, not a substitute for the complete structural frame. The skid structure must be designed to carry the platform, equipment, piping, personnel and other applicable loads.
Confirm the support arrangement
Before selecting the grating panel, confirm the spacing and orientation of the supporting beams or cross-members. The grating manufacturer should provide load and deflection information for the proposed panel type, thickness and span.
Engineering checks should consider the maximum intended loads, including applicable concentrated loads, distributed loads and maintenance activities. The design should also account for the actual support conditions and fastening details.
Check local loads around equipment
Equipment foundations, pipe supports and lifting points can create concentrated loads on the skid frame. These loads should be transferred through the intended structural members rather than relying on the grating surface to support equipment that it was not designed to carry.
Detail the connection between FRP and the frame
Grating clips, bolts or other approved fastening systems should be selected according to the grating profile, support material and project requirements. The connection should resist movement during normal operation and remain suitable for the expected vibration and environmental conditions.
Where FRP grating is installed on a steel frame, the interface should also account for corrosion protection, contact surfaces and access for fastening and inspection.
5. Design Around Pipes, Cables and Equipment Openings
Modular skids often contain dense arrangements of piping, instrumentation and electrical services. Openings in the grating may be necessary to accommodate these components, but they should be planned before fabrication.
Pipe and instrument penetrations
Small openings may be required for pipes, instrument tubing or cable conduits. Their positions and sizes should be coordinated with the final equipment and piping drawings. Where openings interrupt bearing bars, the remaining panel capacity and edge support must be reviewed.
Large equipment access openings
Larger openings may be needed for pump removal, valve maintenance or access to equipment installed below the platform. These openings should have an engineered supporting frame and an appropriate cover or removable panel arrangement.
Cable tray and conduit routing
Electrical and instrumentation routes should be coordinated with the platform layout to prevent trip hazards and avoid obstructing routine access. Cable trays may be routed below the grating or along designated platform edges where the skid design permits.
Maintain suitable separation and accessibility according to the project's electrical and instrumentation requirements. Do not assume that an open-grid floor alone provides adequate cable protection.
6. Consider Guardrails, Toe Plates and Safe Access
Platform flooring is only one part of a safe access system. Skid designers should coordinate the grating with edge protection, stairs, ladders and access gates.
Guardrail and toe plate arrangement
Where required by the applicable project rules, exposed platform edges should be protected with suitable guardrail systems. Toe plates may also be needed to reduce the risk of tools or other objects falling from elevated platforms.
Guardrail posts should connect to structural members designed to resist the required loads. They should not rely on unsupported grating panels as their only anchorage.
Stairs and ladder access
Access points should be located where personnel can enter and leave the platform without passing through congested equipment areas. Stairs or ladders should connect to stable landing areas, and the surrounding grating should be arranged to avoid awkward transitions.
Surface selection
FRP grating may be available with different surface finishes, including molded concave surfaces and grit-coated options. The appropriate choice depends on the expected footwear, moisture, process residue and cleaning conditions. Surface selection should be based on the actual slip-risk assessment rather than appearance alone.
7. Plan for Transportation and Modular Assembly
Unlike a permanent plant platform built entirely on site, a modular skid may be lifted, shipped and repositioned several times before commissioning. The platform design should account for these stages.
Check the transportation envelope
Confirm the overall skid dimensions and applicable transportation restrictions before finalizing the grating layout. Panel sections should be arranged so they can be installed within the available fabrication and shipping envelope.
Protect panels during handling
FRP panels should be supported and protected during storage, lifting and transport. Avoid impact, uncontrolled bending and point loading during handling. Follow the manufacturer's recommendations for stacking, lifting and storage.
Coordinate factory assembly and site installation
Where practical, grating panels can be trial-fitted during skid fabrication. This allows the project team to check panel fit, fastening access and interference with equipment before shipment. If some panels must be removed for transport, their identification and reinstallation sequence should be documented.
For large modular packages, the lifting plan should consider the complete skid assembly and the effects of lifting on the supporting frame and installed components. Grating panels should not be used as lifting points unless specifically designed and approved for that purpose.
8. Information to Include in an FRP Grating Specification
A clear specification helps the grating supplier, skid fabricator and engineering team work from the same design information. The following details should be considered when requesting a quotation or preparing fabrication documents.
- Application: skid type, process service and indoor or outdoor installation.
- Grating type: molded or pultruded FRP grating.
- Resin system: selected according to the chemical and environmental exposure.
- Panel dimensions: overall length, width, thickness and individual panel sizes.
- Load requirements: design loads, support spans, deflection criteria and applicable concentrated loads.
- Surface finish: concave, grit-coated or another specified surface.
- Support details: beam layout, bearing direction and support material.
- Fastening method: clips, bolts or other approved connection details.
- Openings and cutouts: dimensions and locations for pipes, cables and equipment access.
- Safety components: guardrails, toe plates, stairs, ladders and access gates where required.
- Transport requirements: panel handling, packaging, shipping dimensions and installation sequence.
- Documentation: drawings, product data, load tables and relevant test or compliance documents.
9. Common Design Mistakes to Avoid
Several problems can arise when FRP grating is added to a modular skid late in the design process. Common issues include:
- Choosing panels before confirming support spans: grating selection should follow the structural layout and load requirements.
- Ignoring equipment removal paths: maintenance access should include the space needed to remove major components.
- Making unframed openings: large cutouts may interrupt load-bearing bars and require additional structural support.
- Using too many small panels: excessive joints can complicate fastening, inspection and installation.
- Leaving no fastening access: panel connections should remain accessible for installation and future maintenance.
- Overlooking shipping conditions: the panel arrangement should be coordinated with the skid's transport and lifting plan.
- Assuming all FRP products are interchangeable: grating types, resin systems, surface finishes and load capacities vary by product.
10. Conclusion
FRP grating can be a practical flooring option for modular process skids when the project requires a lightweight, corrosion-resistant platform with coordinated maintenance access. Its successful application depends on more than selecting a panel size or surface finish.
Platform layout, structural support, panel segmentation, equipment openings, edge protection and transportation arrangements should be considered as one coordinated design. Early cooperation between the skid designer, structural engineer, fabricator and FRP grating supplier can help reduce installation conflicts and improve long-term access to process equipment.
PREET supplies FRP grating solutions for industrial platforms and access applications. For project-specific recommendations, provide the platform drawings, support spacing, design loads and operating environment for technical review.
Contact PREET
- WhatsApp: +86 138 5147 5666
- Email: info@preet.cn
- Website: www.preetgrating.com
- Product: FRP Molded Grating
