FRP Grating for Tank Farm Access Platforms: Bund Walkways, Valve Access and Drainage Design

Nov 10, 2026

Leave a message

Tank farms are essential parts of oil and gas facilities, chemical plants, fuel terminals and bulk liquid storage installations. They contain storage tanks, transfer pipelines, valves, pumps, meters and other equipment that require regular inspection and operation. Safe access to these components is an important part of tank farm design.

Access platforms and walkways are commonly installed around storage tanks, along pipe racks and near valve stations. In environments exposed to moisture, chemical splashes, salt air or outdoor weather, fiberglass reinforced plastic (FRP) grating can be considered as an alternative to conventional metal flooring.

However, tank farm applications require more than choosing a corrosion-resistant floor panel. The walkway layout must work with tank foundations, pipe routes, containment walls, drainage systems and maintenance procedures. This guide explains the main considerations when specifying FRP grating for tank farm access platforms.

1. Where Is FRP Grating Used in a Tank Farm?

FRP grating can be used in different access areas around aboveground storage tanks and associated process equipment. The specific arrangement depends on the tank configuration, operating requirements and structural design.

Tank perimeter access walkways

Walkways may be installed around selected areas of a storage tank to provide access to inspection points, local instruments, pipe connections and other operating components. FRP grating can provide an open-grid walking surface where the supporting structure has been properly designed.

Valve and manifold platforms

Tank farms often contain groups of isolation valves, control valves and transfer manifolds. Small elevated platforms can help operators reach handwheels, actuators and instrument connections. The platform layout should provide sufficient standing space and clearance for the actual operating tasks.

Pipe rack crossings

Where personnel need to cross pipework or access services on different sides of a pipe rack, elevated walkways and crossover platforms may be required. FRP grating can be installed as the walking surface when its span, load capacity and fastening arrangement are suitable for the support structure.

Tank roof and upper-level access

Some storage tank installations require access to roof-mounted equipment, vents, level instruments or inspection points. FRP grating may be considered for designated walkways and maintenance platforms, subject to the tank design, structural calculations and applicable access requirements.

Industrial tank farm with FRP grating access walkways storage tanks steel support structures and guardrails

2. Why Consider FRP Grating for Tank Farm Walkways?

Tank farms can expose access structures to challenging environmental conditions. FRP grating offers several characteristics that may be useful when the material is matched to the actual service environment.

Corrosion resistance in outdoor environments

Metal platforms in tank farms may be exposed to rain, humidity, salt-laden air, chemical vapors and occasional liquid splashes. FRP grating does not rust like conventional carbon steel and can reduce the need for corrosion-related coating maintenance in suitable applications.

Its chemical resistance depends on the resin system, concentration, temperature and exposure conditions. The selected resin should therefore be checked against the stored product and surrounding chemicals rather than assuming that every FRP formulation is universally resistant.

Lower material weight

FRP grating is generally lighter than comparable steel grating configurations. This can be helpful when designing elevated access structures, retrofitting existing facilities or handling panels during installation. The actual weight advantage depends on the panel type, thickness, mesh and structural arrangement.

Open-grid drainage

The open mesh structure allows rainwater and other liquids to pass through the flooring instead of remaining on a continuous solid surface. This can help reduce standing water on a walkway. Nevertheless, drainage through a grating panel must be evaluated carefully in tank containment areas.

Slip-resistant surface options

FRP grating is available with different surface finishes, including molded concave surfaces and grit-coated surfaces. These options can provide additional traction in wet or contaminated environments. The appropriate finish should be selected according to the expected liquid exposure, footwear and cleaning procedures.

Electrical insulation characteristics

Many standard FRP products have electrically non-conductive characteristics. This may be relevant around certain instrumentation and electrical installations. However, standard FRP grating should not automatically be treated as certified electrical protection or static-control flooring. Hazardous-area classification, bonding, grounding and electrostatic requirements must be addressed separately by the project engineering team.

3. Designing Walkways Inside and Around Bund Walls

Secondary containment, commonly provided by bund walls or diked areas, is a defining feature of many tank farms. It is designed to limit the spread of liquid in the event of a leak or tank failure. Walkway design must not compromise this function.

Maintain the containment boundary

Access routes may need to cross bund walls or enter contained areas. These crossings should be designed as part of the facility's containment and access strategy. A walkway opening, penetration or support detail must not create an uncontrolled route for spilled liquid to escape.

Where a walkway crosses a containment wall, the civil and structural design should address the wall opening, liquid-tight detailing and any required removable or permanent crossing arrangement. The FRP grating itself is not a substitute for a liquid-retaining bund structure.

Coordinate support locations

Walkway supports should be positioned to avoid damaging tank foundations, underground services, containment liners and drainage components. Where supports are located within a bunded area, their bases and connections should be reviewed for compatibility with the containment design.

Provide practical inspection routes

Personnel may need to inspect tank shells, valves, pipe connections and containment areas. Walkways should be arranged to provide access without obstructing visual inspection or emergency response activities.

4. Valve Access Platforms and Pipework Coordination

Valves and pipe connections are among the most frequently accessed components in a tank farm. Platform dimensions and positions should be based on how operators use and maintain this equipment.

Provide adequate operating clearance

Valve platforms should provide enough room for personnel to approach the valve, operate its handwheel or actuator and carry out inspection tasks. The required clearance depends on the equipment size, operating method and maintenance procedure.

Consider actuator and instrument access

Automated valves may have electric, pneumatic or hydraulic actuators. Instrument connections, local indicators and junction boxes may also require access. The platform should not obstruct actuator removal, cable routing or instrument maintenance.

Coordinate pipe penetrations and openings

Grating panels may need cutouts around vertical pipes, supports or instrument connections. These openings should be identified on the drawings before fabrication. Where a cut interrupts load-bearing bars, the remaining panel capacity and edge support must be checked.

Keep access routes clear

Pipework should be coordinated with the walking surface to avoid creating trip hazards or restricting movement. Where pipes pass above or below a walkway, sufficient headroom and maintenance clearance should be maintained according to the project requirements.

5. Drainage and Spill Management Considerations

Drainage is particularly important in tank farms because rainwater, process liquids and accidental spills may collect in different areas. The use of open-grid grating must be coordinated with the facility's liquid collection and containment strategy.

Do not confuse walkway drainage with bund drainage

FRP grating allows water to pass through the floor, but this does not determine where the liquid should go. In a bunded area, liquids passing through the grating may enter the secondary containment space. This can be acceptable only when consistent with the approved facility design and operating procedures.

Review drain locations and discharge controls

Tank farm drainage systems may include collection sumps, controlled drain valves and oil-water separation arrangements. The walkway layout should not block access to these components. Any drainage opening or discharge route must follow the site's environmental and spill-control requirements.

Plan for inspection and cleaning

Open-grid flooring can make it easier to identify accumulated debris below the platform, but it does not eliminate the need for cleaning and inspection. The design should allow personnel to inspect the grating, support members and areas beneath the walkway where access is required.

For facilities subject to the US Spill Prevention, Control, and Countermeasure (SPCC) rule, secondary containment and drainage arrangements should be reviewed against the applicable requirements and the facility's SPCC Plan. Drainage from containment areas must not be treated as ordinary surface-water discharge.

6. Selecting the Right FRP Grating Type

Both molded and pultruded FRP grating may be considered for tank farm platforms. The choice should be based on panel geometry, support span, loading, chemical exposure and project requirements.

Molded FRP grating

Molded grating has a two-directional grid structure and is available in different panel thicknesses, mesh configurations and surface finishes. It can be suitable for platforms with multiple cutouts or irregular layouts, depending on the structural design and manufacturer's load data.

Pultruded FRP grating

Pultruded grating has continuous load-bearing bars and cross rods. Its load-bearing direction must be aligned with the intended support arrangement. It may be considered where longer spans or particular directional loading requirements influence the platform design.

Resin selection

Polyester, vinyl ester and phenolic resin systems may be available depending on the product range. The correct choice depends on the chemicals present, operating temperature, fire-performance requirements and other project conditions. The product supplier should confirm compatibility using the actual exposure information.

Surface finish and color

Concave and grit-coated surfaces are commonly considered where wet or slippery conditions are expected. High-visibility colors may also help identify walkway boundaries and access areas. Color selection should not replace suitable lighting, edge protection or safety markings.

7. Structural Supports, Fasteners and Guardrails

FRP grating panels must be installed on a properly designed support structure. The grating is the walking surface; it should not be assumed to replace the structural frame, foundations or guardrail anchorage.

Check the support span and load requirements

The structural engineer should confirm the maximum intended loads, support spacing, panel orientation and allowable deflection. Load tables from the grating manufacturer should be used for the specific product, thickness and span under consideration.

Select suitable fastening systems

Grating clips, bolts and other approved fasteners should be compatible with the panel and support materials. Fastening details should prevent unintended movement and remain accessible for inspection and maintenance.

Design guardrail connections independently

Guardrails should be connected to structural members capable of carrying the required loads. Posts should not rely solely on unsupported grating panels for anchorage. Toe plates, gates and other edge-protection components should be included where required by the project risk assessment and applicable standards.

Consider the supporting material

FRP grating can be installed on steel, concrete or FRP support structures, depending on the application. The interface should be reviewed for corrosion exposure, fastening compatibility, bearing conditions and long-term inspection access.

8. Tank Farm FRP Grating Specification Checklist

Before requesting a quotation or finalizing a platform design, the project team should prepare the following information:

  • Application location: tank perimeter, valve station, pipe rack, bund crossing or roof access.
  • Operating environment: indoor or outdoor exposure, humidity, salt air and chemical contact.
  • Grating type: molded or pultruded FRP grating.
  • Resin system: selected according to chemical exposure and operating temperature.
  • Panel dimensions: length, width, thickness and mesh size.
  • Support arrangement: beam spacing, bearing direction and support material.
  • Design loads: distributed loads, concentrated loads and applicable maintenance loads.
  • Surface finish: concave, grit-coated or another specified option.
  • Openings: pipe penetrations, equipment clearances and removable access sections.
  • Fastening details: clip type, bolt material and connection arrangement.
  • Safety components: guardrails, toe plates, stairs, ladders and access gates.
  • Containment requirements: bund wall interfaces, drainage paths and spill-control restrictions.
  • Documentation: product data sheets, load tables, drawings and relevant test reports.

9. Common Mistakes When Designing Tank Farm Walkways

Several avoidable design issues can reduce the effectiveness of an access platform or create additional work during installation.

  • Ignoring secondary containment: walkway openings and crossings must not compromise bund integrity or controlled drainage arrangements.
  • Choosing grating before confirming support spans: panel selection should be based on the structural design and verified load data.
  • Leaving insufficient valve clearance: operators need enough room to reach and operate valves and maintain actuators.
  • Making unreinforced cutouts: openings that interrupt load-bearing bars may require additional framing or a revised panel arrangement.
  • Using unsuitable resin systems: chemical compatibility must be checked against the actual stored product and exposure conditions.
  • Overlooking fastener compatibility: clips and bolts should suit both the grating and supporting structure.
  • Neglecting inspection access: supports, drains, containment areas and equipment connections should remain accessible for routine checks.

10. Conclusion

FRP grating can be a useful flooring option for tank farm access platforms, valve stations, pipe rack crossings and selected maintenance walkways. Its corrosion resistance, relatively low weight, open-grid structure and available anti-slip surfaces make it worth considering for suitable industrial environments.

Successful tank farm application depends on coordinated engineering. The grating layout must work with the support structure, tank equipment, containment walls, drainage arrangements and maintenance procedures. Particular care is required to ensure that access improvements do not compromise secondary containment or spill-control functions.

PREET supplies FRP grating solutions for industrial platforms, walkways and access applications. Share your project drawings, support spacing, loading requirements and environmental conditions with our team for product selection and technical review.

Contact PREET

Send Inquiry